Add P155_Smartmeter

docs/source/Plugin/P155.rst

@@ -0,0 +1,177 @@
+.. include:: ../Plugin/_plugin_substitutions_p15x.repl
+.. _P155_page:
+
+|P155_typename|
+==================================================
+
+|P155_shortinfo|
+
+Plugin details
+--------------
+
+Type: |P155_type|
+
+Port Type: |P155_porttype|
+
+Name: |P155_name|
+
+Status ESP32: |P155_status|
+
+Status ESP8266: |P155_status_lb|
+
+GitHub: |P155_github|_
+
+Maintainer: |P155_maintainer|
+
+Used libraries: |P155_usedlibraries|
+
+Hardware
+--------
+This plugin uses an infrared reader to read data via the optical infrared interface of an electricity meter.
+
+.. image:: P155_Meter.png
+
+Devices
+~~~~~~~~~~~~
+
+Supports all smart meters using the SML protocol (Smart Message Language)
+and older meters using the D0 protocol (IEC 62056-21).
+
+Tested devices:
+
+* ebZ DD3 (use model: SML)
+* Holley DTZ541 (use model: SML)
+* Any SML-compliant meter (use model: SML)
+* Older meters with optical interface (use model: D0)
+
+Reading Head
+~~~~~~~~~~~~
+
+To connect a smart meter to the ESP, an IR reading head is required.
+Example for a compatible TTL/UART reading head :
+
+* Hichi TTL, IR Reader
+* bitShake SmartMeterReader - UART | IR Reader
+
+.. image:: P155_IR_Reader.png
+
+The reading head includes a fully assembled PCB with IR diode and phototransistor,
+a ring magnet to attach to the meter, and a housing with cover.
+The plugin uses Hardware Serial which can be configured in ESPEasy UI.
+The meter's serial interface operates at 9600 baud with 3.3V logic levels.
+No level converter is required for 3.3V meters.
+
+Wiring
+~~~~~~~~~~~~
+Example how to connect the Reader to the ESP32 as follows:
+
+.. code-block:: none
+
+  IR-Reader    ESP32
+  TXD        --> GPIO 16 (RX2)
+  RXD        --> GPIO 17 (TX2)
+  VCC        --> 3.3V
+  GND        --> GND
+
+Configuration
+-------------
+
+**Name** A unique name for the task (example: **SmartMeter**).
+
+**Enabled** The device can be enabled or disabled.
+
+**Model Type** Select the protocol matching your meter:
+
+.. csv-table::
+  :header: "Model", "Meter", "Notes"
+  :widths: 8, 15, 20
+
+  "D0", "Older meters with optical interface",""
+  "SML", "All SML-compliant meters", "Dynamic TL parsing, recommended"
+
+.. note::
+
+   Changing the model reloads the page and resets the value selectors.
+
+**Value 1-4** Select the desired measurement values from the available OBIS registers.
+
+.. include:: DataAcquisition.repl
+
+* **Interval**: Recommended 1s for power values, 10s for energy values.
+
+
+Output
+~~~~~~
+
+The available measurement values depend on the selected model.
+
+D0:
+
+.. csv-table::
+  :header: "#", "Value Name", "OBIS", "Unit", "Description"
+  :widths: 2, 12, 12, 4, 15
+
+  "1", "Consumption_kWh", "1-0:1.8.0\*255", "kWh", "Total import energy"
+  "2", "L1_W", "1-0:21.7.0\*255", "W", "Active power L1"
+  "3", "L2_W", "1-0:41.7.0\*255", "W", "Active power L2"
+  "4", "L3_W", "1-0:61.7.0\*255", "W", "Active power L3"
+  "5", "L123_W", "1-0:1.7.0\*255", "W", "Total active power"
+
+SML has the following OBIS codes but not any model sends every code:
+You have to find out with testing. See, for example, the section on DTZ541 below, which has just 3 values to send.
+
+.. csv-table::
+  :header: "#", "Value Name", "OBIS", "Unit", "Description"
+  :widths: 2, 12, 10, 4, 20
+
+  "1", "Energy_Consumption_kWh", "1-0:1.8.0", "kWh \*", "Total import energy"
+  "2", "L1_W", "1-0:21.7.0", "W", "Active power L1"
+  "3", "L2_W", "1-0:41.7.0", "W", "Active power L2"
+  "4", "L3_W", "1-0:61.7.0", "W", "Active power L3"
+  "5", "L123_W", "1-0:16.7.0", "W", "Total active power"
+  "6", "Energy_FeedIn_kWh", "1-0:2.8.0", "kWh \*", "Total export energy"
+  "7", "L1_V", "1-0:32.7.0", "V", "Voltage L1"
+  "8", "L2_V", "1-0:52.7.0", "V", "Voltage L2"
+  "9", "L3_V", "1-0:72.7.0", "V", "Voltage L3"
+  "10", "L1_A", "1-0:31.7.0", "A", "Current L1"
+  "11", "L2_A", "1-0:51.7.0", "A", "Current L2"
+  "12", "L3_A", "1-0:71.7.0", "A", "Current L3"
+
+\* SML delivers energy values in Wh. Enter ``%VALUE%/1000`` in the formula field to get kWh.
+
+DTZ541:
+
+.. csv-table::
+  :header: "#", "Value Name", "OBIS", "Unit", "Description"
+  :widths: 2, 12, 10, 4, 15
+
+  "1", "Energy_Consumption_kWh", "1-0:1.8.0", "kWh", "Total import energy"
+  "2", "L123_W", "1-0:16.7.0", "W", "Total active power"
+  "3", "Energy_FeedIn_kWh", "1-0:2.8.0", "kWh", "Total export energy"
+
+Indicators (recommended settings)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+.. csv-table::
+  :header: "Indicator", "Value Name", "Interval", "Formula", "Extra information"
+  :widths: 12, 10, 5, 8, 20
+
+  "Energy_Consumption_kWh", "Import_kWh", "10", "%VALUE%/1000", "SML only: Wh to kWh"
+  "Energy_FeedIn_kWh", "Export_kWh", "10", "%VALUE%/1000", "SML only: Wh to kWh"
+  "L123_W", "Power_W", "1", "", "No formula needed"
+  "L1_V / L2_V / L3_V", "Voltage_V", "10", "", ""
+
+.. note::
+
+   With **SML**, energy registers deliver the raw value in Wh (scaler is read
+   automatically from the telegram). Enter ``%VALUE%/1000`` in the ESPEasy formula
+   field to get kWh. Power values (W) require no formula.
+
+Change log
+----------
+
+.. versionadded:: 1.0
+  ...
+
+  |added|
+  Initial release version.

docs/source/Plugin/_plugin_substitutions_p15x.repl

@@ -68,6 +68,19 @@
 .. |P154_compileinfo| replace:: `.`
 .. |P154_usedlibraries| replace:: `Adafruit BMP3XX Library`
 
+.. |P155_name| replace:: :cyan:`SML Smartmeter`
+.. |P155_type| replace:: :cyan:`Energy`
+.. |P155_typename| replace:: :cyan:`Energy - SML Smartmeter`
+.. |P155_porttype| replace:: `.`
+.. |P155_status| replace:: :green:`NORMAL`
+.. |P155_status_lb| replace:: ``
+.. |P155_github| replace:: P155_Smartmeter.ino
+.. _P155_github: https://github.com/letscontrolit/ESPEasy/blob/mega/src/_P155_Smartmeter.ino
+.. |P155_usedby| replace:: `.`
+.. |P155_shortinfo| replace:: `SML/D0 Smartmeter energy sensor`
+.. |P155_maintainer| replace:: `Custom`
+.. |P155_compileinfo| replace:: `.`
+
 .. |P159_name| replace:: :cyan:`LD2410`
 .. |P159_type| replace:: :cyan:`Presence`
 .. |P159_typename| replace:: :cyan:`Presence - LD2410`